Description
For straight cuts at 90° only.
Straight cut: Ø 280 mm - 300 x 280 mm - 280 x 280 mm.
Fully enclosed machine, mounted on a robust welded mechanical frame, with tray and lubricant pump.
This machine is equipped with:
Non-switchable 400 V three-phase motor, power 3.0 kW, cutting speeds from 15 to 100 m/min.
Frequency inverter.
Hydraulic cylinder ensuring the descent and raising of the sawing arm (height memorisable).
Cutting force sensor integrated into the guide arm.
Saw frame moving on 2 ball-bearing slides.
Vertical columns filled with aerated concrete to absorb vibrations during sawing.
Left blade guide block moving with the movable jaw of the main vice to ensure the best cutting accuracy.
Hydraulic clamping vices with long stroke and memorised opening, for clamping on the left and right of the blade.
Bar feeder movement by ball screw; motor and hydraulic vice mounted floating.
Bar feeder length 750 mm and multiple stroke repetition (maximum length 7500 mm).
Control panel with colour screen allowing programming of different lengths on the same bar. Each length is linked to a number of pieces.
Piece counter.
Blade rotation stop device at the end of the bar or if the bar is not clamped.
Bar start detection by photoelectric cell.
Minimum clamping: Ø 10 mm.
Remnant length in automatic cycle: 70 mm (150 mm with bundle clamping).
Work table height: approximately 800 mm.
Hydraulic unit.
Motorised chip brush.
Cutting capacities:
Straight cut: Ø 280 mm - 300 x 280 mm - 280 x 280 mm.
Dimensions (L x W x H): 2357 x 2000 x 2339 mm.
In order to meet CE safety standards, the entire machine must have additional peripheral protection depending on its installation.
Price supplement for this machine on request. To do so, please provide us with a layout plan.
Straight cut: Ø 280 mm - 300 x 280 mm - 280 x 280 mm.
Fully enclosed machine, mounted on a robust welded mechanical frame, with tray and lubricant pump.
This machine is equipped with:
Non-switchable 400 V three-phase motor, power 3.0 kW, cutting speeds from 15 to 100 m/min.
Frequency inverter.
Hydraulic cylinder ensuring the descent and raising of the sawing arm (height memorisable).
Cutting force sensor integrated into the guide arm.
Saw frame moving on 2 ball-bearing slides.
Vertical columns filled with aerated concrete to absorb vibrations during sawing.
Left blade guide block moving with the movable jaw of the main vice to ensure the best cutting accuracy.
Hydraulic clamping vices with long stroke and memorised opening, for clamping on the left and right of the blade.
Bar feeder movement by ball screw; motor and hydraulic vice mounted floating.
Bar feeder length 750 mm and multiple stroke repetition (maximum length 7500 mm).
Control panel with colour screen allowing programming of different lengths on the same bar. Each length is linked to a number of pieces.
Piece counter.
Blade rotation stop device at the end of the bar or if the bar is not clamped.
Bar start detection by photoelectric cell.
Minimum clamping: Ø 10 mm.
Remnant length in automatic cycle: 70 mm (150 mm with bundle clamping).
Work table height: approximately 800 mm.
Hydraulic unit.
Motorised chip brush.
Cutting capacities:
Straight cut: Ø 280 mm - 300 x 280 mm - 280 x 280 mm.
Dimensions (L x W x H): 2357 x 2000 x 2339 mm.
In order to meet CE safety standards, the entire machine must have additional peripheral protection depending on its installation.
Price supplement for this machine on request. To do so, please provide us with a layout plan.
Technical specifications
| Category | Production machines |
|---|---|
| Subcategory | Cutting machines |
